Overview of standards
This excerpt from our catalogue of standards is constantly updated and expanded.
Unfortunately, we cannot guarantee that the list is complete. Questions about specific standards or procedures can be sent directly to our employees by phone or via e-mail.
ASTM
- ASTM 1925
- Yellowness Index
- ASTM B 117
- Standard Practice for Opening Salt Spray (Fog) Apparatus
- ASTM B 764
- Standard Test Method for Simultaneous Thickness and Electrode Potential Determination of Individual Layers in Multilayer Nickel Deposit (STEP Test)
- ASTM D 1003
- Test Methods for Haze
- ASTM D 2697
- Standard Test Method for Volume Nonvolatile Matter in Clear or Pigmented Coatings
- ASTM D 2794
- Standard Test Method for Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact)
- ASTM D 968
- Standard Test Method for Abrasion Resistance of Organic Coatings by Falling Abrasive
- ASTM E 313
- Standard Practice for Calculating Yellowness and Whiteness Indices from Instrumentally Measured Color Coordinates
- ASTM E 424
- Standard Test Methods for Solar Energy Transmittance and Reflectance (Terrestrical) of Sheet Materials
- ASTM G 173
- Standard Tables for References Solar Spectral Irradiance at Air Mass 1.5
- ASTM G 85
- Standard Practice for Modified Sal Spray (Fog) Testing
- ASTM G 85-A3
- Acidified Synthetic Sea Water Testing (SWAAT Test)
- ASTM G 69
- Standard Test Method for Measurement of Corrosion Potentials of Aluminium Alloys
BMW
- AA-0026
- Aging resistance test
- AA-0053
- Sun cream resistance of painted parts in the interior
- AA-0054
- Resistance of Coatings to Car-wash Machines
- AA-0055
- Chemical resistance test of surfaces
- AA-0061
- Bestimmung der Emission von Formaldehyd aus nichtmetallischen Werkstoffen und Bauteilen mittels HPLC
- AA-0079
- Determination of multi impact stone chip resistance
- AA-0101
- Reflectometer Value (Gloss)
- AA-0129
- Cass Testing ( Copper chloride-acetic acid salt spray testing)
- AA-0134
- Dry scratch resistance test using Crockmeter
- AA-0136
- Testing of Resistance to Pressure Water Jet (Steam Jet Test)
- AA-0161
- Color Measurement on Bodies and Hang On Parts
- AA-0168
- Filiform Corrosion on coated Aluminium
- AA-0169
- Out-door weathering test
- AA-0171
- Outdoor weathering of coatings at Florida, USA
- AA-0175
- Galvanostatic Cathodic Polarization Corrosion Short-Term Test on Coated Steel
- AA-0180
- Cross hatch testing
- AA-0187
- Adhesion test at low temperature by bowl drop test on process materials
- AA-0203
- Hydrolysis Test
- AA-0213
- Condensation Water Constant Atmosphere Test
- AA-0224
- Cyclic Corrosion Test
- AA-0235
- Accelerated weathering crack stability
- AA-0236
- Accelerated weathering colour stability
- AA-0244
- Paint Compatibility Test
- AA-0246
- Placing of test samples in corrosion test
- AA-0257
- Measurement of structure and gloss on painted surfaces
- AA-0264
- Multi-stone chip test with salt water exposure
- AA-0324
- Saltspray - Test
- AA-0326
- SCAB corrosion test
- AA-0354
- Technical Understanding of Color Measurement and the Measurement of Test Panels for Initial and Batch Release
- AA-0365
- Check of the adhesionforce for the tape 4657 grey for bondingtesting
- AA-0403
- Visual Color Comparison and Metamerism Test
- AA-0471
- Abrasion Resistance using the Abrex Test Equipment
- AA-P 175
- Cylic Corrosion Test
- AA-P 184
- Saltspray-test
- AA-P 187
- Multi-stone chip test with salt water exposure
- AA-P 192
- Determination of multi impact stone chip resistance
- AA-P 224
- Condensation Water Constant Atmosphere Test
- AA-P 275
- Aging resistance test
- AA-P 276
- Temperature Cycle Test
- AA-P 277
- Humidity / LowTemperature Load
- GS 90011
- Coating of parts made of metallic materials by means of organic materials
- GS 93036
- Light Weight Reinforced Thermoplast im Exteriuer
- GS 94007
- Painted plastics parts
- GS 97003-1
- Surface classification for painted motor vehicles
- GS 97017
- Coatings on plastic parts - Electroplated plastic parts
- GS 97034
- Manual abrasion test (ABREX)
- GS 97034-9
- Scratch test
- PR 231
- Functional test
- PR 292
- Attachments underbody - gas chromatography / mass spectrometry (Pyrolysis-GC-MS)
- PR 303.5 A-D
- Climate cycle test
- PR 308.1
- Climatic testing of adhesive joints
- PR 308.2
- Climatic testing of adhesive connections and of adhesive joints
- QV 36009
- Surface condition testing of wheels
Bentley
- CQS No: 119
- Crewe Quality Specification
- CQS No: 154
- Crewe Quality Specification
- CQS No: 199
- Crewe Quality Specification
Chrysler
- LP-463DD-18-01
- Scratch and Mar Resistance of Automotive Interior Coatings and exterior plastik using 5-finger-Test
- LP-463LB-13-01
- HEAT AGING OF TRIM MATERIALS
- LP-463PB-22-01
- Cycle testing of painted surfaces
- LP-463PB-31-01
- RESISTANCE TO VARIOUS FLUIDS
- LP-463PB-64-01
- THERMAL SHOCK PROCEDURE FOR ORGANIC COATING ADHESION TEST
DIN EN
- DIN EN 1062-11
- Methods of conditioning before testing
- DIN EN 1062-3
- Determination of liquid water permeability
- DIN EN 1081
- Spezifischer Durchgangswiderstand
- DIN EN 12540 Anhang E
- Dubpernell test method
- DIN EN 13300
- Paints and varnishes - Water-borne coating materials and coating systems for interior walls and ceilings - Classification
- DIN EN 1372
- Test method for adhesives for floor and wall coverings - Peel test
- DIN EN 13523-27
- Coil coated metals - Test methods - Part 27: Resistance to humid poultice (Cataplasm test)
- DIN EN 1373
- Test method for adhesives for floor and wall covering - Shear test
- DIN EN 14370
- Determination of surface tension (coating materials, polymer dispersion, rubber and latices, surfaceactive substances)
- DIN EN 1464
- Determination of peel resistance of adhesive bonds - Floating roller method
- DIN EN 1465
- Determination of tensile lap-shear strength of bonded assemblies
- DIN EN 1542
- Measurement of bond strength by pull-off
- DIN EN 16094
- Laminate floor coverings - Test method for the determination of micro-scratch resistance
- DIN EN 166
- Personal eye protection - Specifications
- DIN EN 169
- Personal eye protection - Filters for welding and related techniques
- DIN EN 170
- Personal eye protection - Ultraviolet filters
- DIN EN 171
- Personal eye protection - Infrared filters
- DIN EN 172
- Personal eye protection - Sunglare filters for industrial use
- DIN EN 1767
- Infrared analysis
- DIN EN 1863
- Glass in building - Heat strengthened soda lime silicate glass
- DIN EN 20105-A02
- Textiles - Tests for colour fastness - Part A02: Grey scale for assessing change in colour
- DIN EN 3665
- Filiform corrosion resistance test on aluminium alloys
- DIN EN 410:2011
- Glass in building - Determination of luminous and solar characteristics of glazing
- DIN EN 60068-2-14
- Environmental testing - Test N: Change of temperature
- DIN EN 60068-2-30
- Environmental testing - Test Db: Damp heat, cyclic
- DIN EN 60068-2-38
- Environmental testing - Test Z/AD: Composite temperature/humidity cyclic test
- DIN EN 60068-2-70
- Environmental testing - Test Xb: Abrasion of markings and letterings by rubbing of fingers and hands
- DIN EN 60079-0
- Explosives atmospheres - Equipment and general requirements
- DIN EN 60216-1
- Thermal endurance properties - Part 1: Ageing procedures and evaluation of test results
- DIN EN 60216-2
- Determination of thermal endurance properties of electrical insulating materials - choice of test criteria
- DIN EN 60216-5
- Determination of relative thermal endurance index (RTE) of an insulating material
- DIN EN 60243-1
- Electric strenght of insulating materials - Test methods - Part 1: Tests at power frequencies
- DIN EN 61074
- Testing methods for the determination of heats and temperatures of melting and crystallization of eletrical insulating materials by differential scanning calorimetry
- DIN EN 71-3
- Safety of toys - Part 3: Migration of certain elements
- DIN EN 828
- Adhesives - Wettability - Determination by measurement of contact angle and surface free energy of solid surface
- DIN EN 927-3
- Coating materials and coating systems for exterior wood - Part 3: Natural weathering test
- DIN EN 927-5
- Coating materials and coating systems for exterior wood - Part 5: Assessment of the liquid water permeability
- DIN EN 927-6
- Coating materials and sytems for exterior wood - Part 6: Exposure of wood coatings to artificial weathering using fluorescent UV lamps and water
DIN EN ISO
- DIN EN ISO 105-A03
- ---
- DIN EN ISO 105-B02
- Colour fastness to artificial light: Xenon arc fading lamp test
- DIN EN ISO 105-X12
- Colour fastness to rubbing
- DIN EN ISO 11357-2
- Differential scanning calorimetry (DSC) - Part 2: Determination of glass transition temperature and glass transition step height
- DIN EN ISO 11357-3
- Differential scanning calorimetry (DSC) - Part 3: Determination of temperature and enthalpy of melting and crystallization
- DIN EN ISO 11357-4
- Differential scanning calorimetry (DSC) - Part 4: Determination of specific heat capacity
- DIN EN ISO 11357-5
- Differential scanning calorimetry (DSC) - Part 5: Determination of characteristic reaction-curve temperatures and times, enthalpy of reaction and degree of conversion
- DIN EN ISO 11664-1
- Colorimetry - Part 1: CIE standard colorimetric observers
- DIN EN ISO 11664-2
- Colorimetry - Part 2: CIE standard illuminants
- DIN EN ISO 11664-3
- Colorimetry - Part 3: CIE standard tristimulus values
- DIN EN ISO 11664-4
- Colorimetry - Part 4: CIE 1976 L*a*b* Colour space
- DIN EN ISO 11664-5
- Colorimetry - Part 5: CIE 1976 L*u*v* Colour space and u', v' uniform chromaticity scale diagram
- DIN EN ISO 1183-1
- The density of non-cellular plastics - Part 1: Immersion method, liquid pyknometer method, titration method
- DIN EN ISO 11890-1
- Determination of volatile organic compound (VOC) content - Part 1: Difference method
- DIN EN ISO 11890-2
- Determination of volatile organic compound (VOC) content - Part 2: Gas-chromatographic method
- DIN EN ISO 11909
- Polyisocyanate resins - General testing methods
- DIN EN ISO 11997-1
- Determination of resistance to cyclic corrosion conditions - Part 1: wet (salt fog)/dry/humid
- DIN EN ISO 11998
- Determination of wet-scrub resistance and cleanability of coatings
- DIN EN ISO 12944-1
- Paints and varnishes - Corrosion protection of steel structures by protective paint systems – Part 1: General introduction
- DIN EN ISO 12944-2
- Paints and varnishes - Corrosion protection of steel structures by protective paint systems – Part 2: Classification of environments
- DIN EN ISO 12944-5
- Paints and varnishes - Corrosion protection of steel structures by protective paint systems - Part 5: Protective paint systems
- DIN EN ISO 12944-6
- Paints and varnishes - Corrosion protection of steel structures by protective paint systems – Part 6: Laboratory performance test methods
- DIN EN ISO 12944-9
- Paints and varnishes - Corrosion protection of steel structures by protective paint systems – Part 9: Protective paint systems and laboratory performance test methods for offshore and related structures
- DIN EN ISO 13803
- Determination of haze on paint films at 20°
- DIN EN ISO 13937-2
- Tear properties of fabrics - Part 2: Determination of tear force of trouser-shaped test specimens (single tear method)
- DIN EN ISO 14125
- Fibre-reinforced plastic composites - Determination of flexural properties
- DIN EN ISO 14577-1
- Instrumented indentation test for hardness and materials parameters - Part 1: Test method
- DIN EN ISO 14577-2
- Instrumented indentation test for hardness and materials parameters - Part 2: Verification and calibration of testing machines
- DIN EN ISO 14577-3
- Instrumented indentation test for hardness and materials parameters - Part 3: Calibration of reference blocks
- DIN EN ISO 14577-4
- Instrumented indentation test for hardness and materials parameters - Part 4: Test method for metallic and non-metallic coatings
- DIN EN ISO 1463
- Measurement of coating thickness - Microscopical method
- DIN EN ISO 14680-1
- Determination of pigment content - Part 1: Centrifuge method
- DIN EN ISO 14680-2
- Determination of pigment content - Part 2: Ashing method
- DIN EN ISO 1516
- Determination of flash/no flash - Closed cup equilibrium
- DIN EN ISO 1518-1
- Determination of scratch resistance - Part 1: Constant-loading method
- DIN EN ISO 1519
- Bend test (cylindrical mandrel)
- DIN EN ISO 1520
- Cupping test
- DIN EN ISO 1522
- Pendulum damping test
- DIN EN ISO 1523
- Determination of flash point - Closed cup equilibrium method
- DIN EN ISO 1524
- Determination of fineness of grind
- DIN EN ISO 15711
- Determination of resistance to cathodic disbonding of coatings exposed to sea water
- DIN EN ISO 16000-10
- Determination of the emission of VOC (volatile organic compounds) from building products and furnishing - Emission test cell method
- DIN EN ISO 16000-3
- Determination of formaldehyde and other carbonyl compounds in indoor air and test chamber air - Active sampling method
- DIN EN ISO 16000-6
- Determination of VOC in indoor and test chamber air by active sampling on Tenax TA®sorbent, thermal desorption and gas chromatography using MS or MS-FID
- DIN EN ISO 16000‑9
- Determination of the emission of VOC from building products and furnishing - Emission test chamber method
- DIN EN ISO 16276-1
- Corrosion protection of steel structures by protective paint systems - Assessment of, and acceptance criteria for, the adhesion/cohesion (fracture strength) of a coating - Part 1: Pull-off testing
- DIN EN ISO 16276-2
- Corrosion protection of steel structures by protective paint systems - Assessment of, and acceptance criteria for, the adhesion/cohesion (fracture strength) of a coating - Part 2: Cross-cut testing and X-cut testing
- DIN EN ISO 16474-2
- Methods of exposure to laboratory light sources - Part 2: Xenon-arc lamps
- DIN EN ISO 16474-3
- Methods of exposure to laboratory light sources - Part 3: Fluorescent UV lamps
- DIN EN ISO 16773-1
- Electrochemical impedance spectroscopy (EIS) on coated and uncoated metallic specimens - Part 1: Terms and definitions
- DIN EN ISO 16773-2
- Electrochemical impedance spectroscopy (EIS) on coated and uncoated metallic specimens - Part 2: Collection of data
- DIN EN ISO 16773-3
- Electrochemical impedance spectroscopy (EIS) on coated and uncoated metallic specimens - Part 3: Processing and analysis of data from dummy cells
- DIN EN ISO 16925
- Determination of the resistance of coatings to pressure water-jetting
- DIN EN ISO 178
- Determination of flexural properties
- DIN EN ISO 17895
- Determination of the volatile organic compound content of low-VOC emulsion paints (in-can VOC)
- DIN EN ISO 20567-1
- Determination of stone-chip resistance of coatings - Part 1: Multi-impact testing
- DIN EN ISO 2114
- Determination of partial acid value and total acid value
- DIN EN ISO 2177
- Measurement of coating thickness - Coulometric method by anodic dissolution
- DIN EN ISO 2178
- Nichtmagnetische Überzüge auf magnetischen Grundmetallen - Messen der Schichtdicke - Magnetverfahren
- DIN EN ISO 2360
- Measurement of coating thickness - Amplitude-sensitive eddy-current method
- DIN EN ISO 2409
- Cross-cut test
- DIN EN ISO 2431
- Determination of flow time by use of flow cups
- DIN EN ISO 2808
- Determination of film thickness
- DIN EN ISO 2808 (Verfahren 6A)
- Determination of film thickness - Microscopic method
- DIN EN ISO 2808 (Verfahren 6B)
- Determination of film thickness - Wedge-cut method
- DIN EN ISO 2808 (Verfahren 7C)
- Determination of film thickness - Magnetic method
- DIN EN ISO 2808 (Verfahren 7D)
- Non-magnetic coatings on magnetic substrates - Measurement of coating thickness - Magnetic method
- DIN EN ISO 2810
- Natural weathering of coatings - Exposure and assessment
- DIN EN ISO 2811-1
- Determination of density - Part 1: Pycnometer method
- DIN EN ISO 2812
- Determination of resistance to liquids
- DIN EN ISO 2812-1
- Determination of resistance to liquids - Part 1: Immersion in liquids other than water
- DIN EN ISO 2812-2
- Determination of resistance to liquids - Part 2: Water immersion method
- DIN EN ISO 2812-3
- Determination of resistance to liquids - Part 3: Method using an absorbent medium
- DIN EN ISO 2812-4
- Determination of resistance to liquids - Part 4: Spotting methods
- DIN EN ISO 2812-5
- Determination of resistance to liquids - Part 5: Temperature-gradient oven method
- DIN EN ISO 2813
- Determination of gloss value at 20°, 60° und 85°
- DIN EN ISO 2815
- Buchholz indentation test
- DIN EN ISO 2884-1
- Determination of viscosity using rotary viscometers - Part 1: Cone-and-plate viscometer operated at a high rate of shear
- DIN EN ISO 3001
- Epoxidäquivalent
- DIN EN ISO 3146
- Determination of melting behaviour of semi-crystalline polymers by capillary tube and polarizing-microscope methods
- DIN EN ISO 3219
- Polymers/resins - Determination of viscosity using a rotational viscometer with defined shear rate
- DIN EN ISO 3231
- Determination of resistance to humid atmospheres containing sulfur dioxide
- DIN EN ISO 3233
- Determination of dry-film density
- DIN EN ISO 3233-2
- Method using the determination of non-volatile-matter content and determination of the dry film density on coated test panels (Archimedes principle)
- DIN EN ISO 3248
- Determination of the effect of heat
- DIN EN ISO 3251
- Determination of non-volatile-matter content
- DIN EN ISO 3497
- Measurement of coating thickness - X-ray spectrometric methods
- DIN EN ISO 3961
- Determination of iodine value
- DIN EN ISO 3892
- Determination of coating mass per unit area - Gravimetric methods
- DIN EN ISO 4288
- Geometrical Product Specifications (GPS) - Surface texture: Profile method
- DIN EN ISO 4623-1
- Determination of resistance to filiform corrosion - Part 1: Steel substrates
- DIN EN ISO 4623-2
- Determination of resistance to filiform corrosion - Part 2: Aluminium substrates
- DIN EN ISO 4624
- Pull-off test for adhesion
- DIN EN ISO 4628-1
- Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance - Part 1: General introduction and designation system
- DIN EN ISO 4628-10
- Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance - Part 10: Assessment of degree of filiform corrosion
- DIN EN ISO 4628-2
- Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance - Part 2: Assessment of degree of blistering
- DIN EN ISO 4628-3
- Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance - Part 3: Assessment of degree of rusting
- DIN EN ISO 4628-4
- Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance - Part 4: Assessment of degree of cracking
- DIN EN ISO 4628-5
- Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance - Part 5: Assessment of degree of flaking
- DIN EN ISO 4628-8
- Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance - Part 8: Assessment of degree of delamination and corrosion around a scribe or other artificial defect
- DIN EN ISO 4629
- Determination of hydroxyl value
- DIN EN ISO 4892-2
- Methods of exposure to laboratory light sources - Part 2: Xenon-arc lamps
- DIN EN ISO 4892-3
- Methods of exposure to laboratory light sources - Part 3: Fluorescent UV lamps
- DIN EN ISO 527-1
- Determination of tensile properties - Part 1: General principles
- DIN EN ISO 527-2
- Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics
- DIN EN ISO 527-3
- Determination of tensile properties - Part 3: Test conditions for films and sheets
- DIN EN ISO 527-4
- Plastics - Determination of tensile properties - Part 4: Test conditions for isotropic and anisotropic fibre-reinforced plastic composites
- DIN EN ISO 527-5
- Plastics - Determination of tensile properties - Part 5: Test conditions for unidirectional fibre-reinforced plastic composites
- DIN EN ISO 6270-1
- Determination of resistance to humidity - Part 1: Condensation (single-sided exposure)
- DIN EN ISO 6270-2
- Determination of resistance to humidity - Part 2: Condensation (in-cabinet exposure with heated water reservoir)
- DIN EN ISO 6272-1
- Rapid-deformation (impact resistance) tests - Part 1: Falling-weight test, large-area indenter
- DIN EN ISO 6504-3
- Determination of hiding power - Part 3: Determination of contrast ratio of light-coloured paints at a fixed spreading rate
- DIN EN ISO 6860
- Bend test (conical mandrel)
- DIN EN ISO 6892-1
- Tensile tesing - Part 1: Method of test at room temperature
- DIN EN ISO 6988
- Metallic and other non-organic coatings - Sulfur dioxide test with general condensation of moisture
- DIN EN ISO 7783
- Determination of water-vapour transmission properties - Cup method
- DIN EN ISO 7784-1
- Determination of resistance to abrasion - Part 1: method with abrasive-paper covered wheels and rotating test specimen
- DIN EN ISO 7784-2
- Determination of resistance to abrasion - Part 2: method with abrasive rubber wheels and rotating test specimen
- DIN EN ISO 8130-10
- Coating powders - Part 10: Determination of desposition efficiency
- DIN EN ISO 8130-11
- Coating powders - Part 11: Inclined-plane flow test
- DIN EN ISO 8130-12
- Coating powders - Part 12: Determination of compatibility
- DIN EN ISO 8130-13
- Coating powders - Part 13: Particle size analysis by laser diffraction
- DIN EN ISO 8130-2
- Coating powders - Part 2: Determination of density by gas comparison pyknometer (referee method)
- DIN EN ISO 8130-5
- Coating powders - Part 5: Determination of flow properties of a powder/air mixture
- DIN EN ISO 8130-6
- Coating powders - Part 6: Determination of gel time of thermosetting coating powders at a given temperature
- DIN EN ISO 8130-7
- Coating powders - Part 7: Determination of loss of mass on stoving
- DIN EN ISO 8130-8
- Coating powders - Part 8: Assessment of the storage stability of thermosetting powders
- DIN EN ISO 8295
- Determination of the coefficients of friction
- DIN EN ISO 8501-1
- Visual assessment of surface cleanliness - Part 1: Rust grades and preparation grades
- DIN EN ISO 8503-1
- Specifications and definition for ISO surface profile comparators for the assessment of abrasive blast-cleaned surfaces
- DIN EN ISO 8503-2
- Method for the grading of surface profile of abrasive blast-cleaned steel - Comparator procedure
- DIN EN ISO 8503-3
- Method for the calibration of ISO surface profile comparators and for the determination of surface profile (focus: microscope procedure)
- DIN EN ISO 8503-4
- Method for the calibration of ISO surface profile comparators and for the determination of surface profile (Stylus instrument procedure)
- DIN EN ISO 9117-1
- Drying tests - Part 1: Determination of through-dry state and through-dry time
- DIN EN ISO 9117-2
- Drying tests - Part 2: Pressure test for stackability
- DIN EN ISO 9117-3
- Drying tests - Part 3: Surface-drying test using ballotini
- DIN EN ISO 9117-4
- Drying tests - Part 4: Test using a mechanical recorder
- DIN EN ISO 9117-5
- Drying tests - Part 5: Modified Bandow-Wolff test
- DIN EN ISO 9117-6
- Drying tests - Part 6: Print-free test
- DIN EN ISO 9227
- Corrosion tests in artificial atmospheres - Salt spray tests
DIN, DIN SPEC
- DIN 16945
- Amine number (Testing of resins, hardeners and accelerators, and catalyzed resins )
- DIN 25415-1
- Radioactively contaminated surfaces – Method for testing and assessing the ease of decontamination
- DIN 30646
- Self-adhesive signs – Testing of delivery conditions
- DIN 38405
- wet chemical determination of chromium (VI)
- DIN 50018
- Testing in a saturated atmosphere in the presence of sulfur dioxide
- DIN 5023
- Painting box with opaque colours
- DIN 5033-1
- Colorimetry – Part 1: Basic terms of colorimetry
- DIN 5033-7
- Colorimetry – Part 7: Measuring conditions for object colours
- DIN 5033-8
- Colorimetry: Measuring for light sources
- DIN 5033-9
- Colorimetry – Part 9: Reflectance standard for calibration in colorimetry and photometry
- DIN 50918
- Corrosion of metals – Electrochemical corrosion tests
- DIN 50986
- Wedge-cut method
- DIN 51405
- Phthalate plasticisers
- DIN 51425
- Testings of mineral oil hydrocarbons and similar materials - high pressure liquid chromatography
- DIN 51451
- Infrared Spectrometry
- DIN 53019-1
- Viscosimetry - Measurement of viscosities and flow curves by means of rotational viscometers
- DIN 53019-2
- Viscosimetry - Measurement of viscosities and flow curves by means of rotational viscometers
- DIN 53019-3
- Viscosimetry - Measurement of viscosities and flow curves by means of rotational viscometers
- DIN 53100
- Metallic coatings
- DIN 53100 Anhang C
- Dubpernell test method
- DIN 53154
- Shot peening method
- DIN 53233
- Paints and varnishes - Determination of abraison behaviour
- DIN 53240-2
- Determination of hydroxyl value - Part 2
- DIN 53357
- Diverse testing methods for underbody panels
- DIN 53409
- one-dimensional colour index (such as Pt-Co, APHA-, Hazen-, Iodine- and Gardner-colour index)
- DIN 53504
- Testing of rubber - Tensile test
- DIN 53914
- Testing of surface active agents
- DIN 55659-1
- Determination of pH value - Part 1: pH- electrodes with glass membrane
- DIN 55665
- Natural weathering of coatings - Determination of corrosion protection performance
- DIN 55670
- Method for Testing paint coatings for pores and cracks using high-voltage
- DIN 55991-1
- Coatings for nuclear facilities - Part 1: Requirements and test methods
- DIN 61340-2-1
- Electrostatics - Part 2-1
- DIN 61340-3
- Electrostatics - Part 3
- DIN 6167
- Description of yellowness of near-white or near-colourless materials
- DIN 6175-1
- Tolerances for automotive paints - Part 1: Uni paints
- DIN 6175-2
- Tolerances for automotive paints - Part 2: Goniochromatic paints
- DIN 75200
- Determination of burning behaviour of interior materials in motor vehicles
- DIN 75201
- Determination of the fogging characteristics of trim materials in the interior of automobiles
- DIN SPEC 91032
- Coating materials and coating systems for exterior wood
- DIN SPEC 91033
- Resistance to blocking of paints and varnishes on wood
Daimler
- 060.2007.OQM.000565.01
- Sonderfahrzeug Muster
- Daimler Chrysler Klimawechseltest (KWT DC) PA PP PWT 3001
- Klimawechseltest
- DBL 4040
- Rohre für Brems- und Kraftstoffsysteme
- DBL 4062
- Liefervorschrift ; Elektrolytisch verzinktes Flachzeug
- DBL 4917
- Liefervorschrift ; gegossene Integralträger aus Aluminium
- DBL 5010
- Liefervorschrift ; Aggregate-Gußteile aus Mg
- DBL 5306
- Liefervorschrift ; Allgemeine technische Lieferbedingungen und Prüfverfahren für Innenausstattungsmaterialien und ähnliche Produkte
- DBL 5399
- Liefervorschrift ; Anschmutzen / Reinigen bei Innenausstattungsteilen /-materialien
- DBL 5400
- Liefervorschrift ; Teile aus glasfaserverstärktem Duroplastkunststoffen
- DBL 5404
- Liefervorschrift ; Teile aus thermoplastischen Kunststoffen für den direkten und indirekten Bereich des Fahrgastinnenraumes, für Fahrgastraumheizung, Fahrgastraumbelüftung, Verkleidungen und Gehäuse
- DBL 5416
- Supply Specification ; Parts Manufactured from Thermoplastics for Paneling, Housings and Functional Parts for External Applications
- DBL 5555
- Finished Parts and Semi-Finished Products Made of Organic Polymer Materials General Conditions and Test Methods
- DBL 5578
- Gleitlackbeschichtete Elastomerteile
- DBL 6515
- Supply Specification ; Determination of the technical cleanliness of components
- DBL 7260
- Liefervorschrift ; Kunstharz- Einbrenn-Decklack
- DBL 7305
- Liefervorschrift ; Lacke für Achsen, Lenkrad, Gelenkwellen und andere Anbauteile, luft- und wärmetrocknend
- DBL 7381
- Organic Coating for Metallic Parts on the Vehicle Exterior
- DBL 7381.30
- Freigabeumfänge für Radoberflächen
- DBL 7382
- Supply Specification ; Coating of Metallic Parts in Vehicle Interiors
- DBL 7384
- Supply Specification ; Coating of plastic parts in vehicle interiors
- DBL 7385
- Liefervorschrift ; Ein- oder Mehrschichtanstrich für Holz-Zierteilchen
- DBL 7390
- Grundlackierung (Grundierung) als Basis für nachfolgende Fertiglackierungen
- DBL 7391
- Supply Specification ; Coating / Painting for Parts with High Corrosive Stress
- DBL 7392
- Liefervorschrift ; Beschichtung / Lackierung mit mäßiger Korrosionsbeanspruchung
- DBL 7397
- Kondenswasserbeständiger Anstrich
- DBL 7399
- Supply Specification ; Enamels, paints and similar coating materials and associated coatings. General conditions and tests
- DBL 8230
- Liefervorschrift ; selbstklebende Schilder
- DBL 8427
- Korrosionsschutzbeschichtung für Bauteile aus einwandig geschweißten Stahlrohren
- DBL 8440
- Teile aus Eisenwerkstoffen mit anorganischer Beschichtung ( Zinklamellenüberzug)
- DBL 8451
- Liefervorschrift ; Galvanische abgeschiedene Zink- und Zinklegierungsbeschichtungen für Bauteile aus Eisenwerkstoffen
- DBL 8459
- Liefervorschrift ; Teile mit Nickel-, Nickel-Chrom- oder Kupfer-Nickel-Chrom-Überzügen
- DBL 8465
- Electroplated Parts Manufactured from Plastics with Metallic and Additional Coatings
- DBL 8465
- Liefervorschrift ; Galvanisierte Teile aus Kunststoffen mit metallischen Überzügen und Zusatzbeschichtungen Vorwort
- DBL 9202
- Liefervorschrift ; Zierteile im Fahrzeuginnenraum
- DBL 9440
- Liefervorschrift ; Verbindungselement mit metrischen Gewinde Oberflächenschutz und ergänzenden technischen Lieferbedingungen
- DIN 55662-B
- Dampfwasserstrahlprüfung
- GSP_ORW_PAK_02d.docx
- Vorgaben für das Prüfinstitut zu den Prüfverfahren und Ergebnisdokumentation der Probenkörper
- GSP_ORW_PAK_03d.docx
- Vorgaben für das Prüfinstitut zu den Prüfverfahren und Ergebnisdokumentation der Probekörper
- GSP_ORW_PAK_03e.docx
- Specifications for Testing Institutes on Test Procedures and Documentation of Results
- GSP_ORW_PAK_12d.docx
- Vorgaben für das Prüfinstitut zu den Prüfverfahren und Ergebnisdokumentation der Probekörper
- LPV 0700.99000
- Prüfung auf Lackverträglichkeit
- LPV K 6
- Lacktechnische Prüfvorschrift für lackierte Kunststoffteile im Motorraum
- PAPP PWT 3002
- Filiformprüfung an lackierten Aluminiumteilen
- PBODC360
- Haftfestigkeit (Kratzprobe, Adhäsionshaftung [Klebebandmethode])
- PBODC371
- Prüfung auf Chemikalienbeständigkeit
Deutsche Bahn
- DBS 918 020
- Beschriftung von Schienenfahrzeugen - Selbstklebefolien für Außenbeschriftung und -werbung
- DBS 918 021
- Beschriftung von Schienenfahrzeugen - Selbstklebefolien für Innenbeschriftung
Fiat
- 40449
- Scratch Hardness/ Surface abrasions TEST for Paints and /or Platic backing using Brush tester
- 40451
- Accelerated aging by atmospheric agents
- 50180
- Corrosions TEST
- 50184
- Klima TEST
- 50457
- Test for nonmetallic Materials Specular gloss determination for paints , varnishes and enamels by glossmeter
- 50461
- Adhesion Test of inorganic and organic trims by squaring of
- 50470
- Water ristance test flor decorations and paints
- 50473
- DETERMINATION OF THERESISTANCE TO GASOLINE OF PAINTS, ENAMELS AND RELATED Products
- 50488
- DETERMINATION OF ABRASION RESISTANCE OF PROTECTIVE COATINGS BY METALLIC GRIT---BLASTING
- 955842
- VARIOUS METALLIC Part Painting
- 955846
- Products for tempory Bodywork Protecion
- 50452/02
- PENCIL HARDNESS TEST FOR ORGANIC Coatings
- 50471/ 01
- Alternating ultraviolet radiation/ humidity ristance test
- 50473 / 01
- DETERMINATION OF THE RESISTANCE TO CHEMICAL AGENTS OF PRODUCTS
- 50488/01
- CHIP RESISTANCE TEST FOR PAINTS, ENAMELS, PROTECTIVE COATINGS AND RELATED PRODUCTS
- 50488/02
- DETERMINATION OF THE RESISTANCE TO FRETTING OF FINISHING PAINTS
- 50493/04
- ORGANIC COATINGS Determination of the resistance to scab---indoor corrosion
- 7- - M001
- Evaluation of the colour of injection - moulded thermoplastic materials
- 7- - M002
- EVALUATION OF THE GLOSS OF PLASTIK MATERIALS
- 9. 55846
- Products for tempory Bodywork Protecion
- 9.03141/04
- CONSOLES ON THE TUNNEL
- 9.03178/01
- DRIVER AND PASSENGER Airbag Moduls
- 9.55842/01
- AESTHETIC AND OPERATIONAL FINISHING OF PARTS MADE OF PLASTIC MATERIALS OBTAINED BY PAINTING OR OTHER PROCESSES
Ford
- BI 007-01
- CHIP RESISTANCE TEST FOR PAINTED PANELS
- BI 103-01
- SALT SPRAY RESISTANCE TEST FOR PAINTED PANELS AND PARTS
- BI 103-02
- Preporation of panels for paint test
- BI 104-01
- WATER IMMERSION TEST FOR PAINTED PARTS AND PANELS
- BI 104-02
- CONDENSING WATER VAPOR TEST
- BI 106-01
- COATING ADHESION TEST
- BI 109-01
- VISUAL APPEARANCE EVALUATION
- BI 110-01
- MEASUREMENT OF THE GLOSS OF PAINT PANELS
- BI 113-01
- WATER AND SOAP SPOTTING TEST FOR PAINT
- BI 113-02
- RESISTANCE TO ACID SPOTTING
- BI 113-03
- RESISTANCE TO Synthetic perspiraton staining
- BI 113-06
- TEST METHOD FOR RESISTANCE TO PERSPIRATION
- BI 113-08
- RESISTANCE TO SUNSCREEN LOTION AND INSECT REPELLENT
- BI 117-01
- THICKNESS MEASUREMENT OF PAINT FILMS
- BI 123-01
- painted sheet metal CORROSION TEST
- BI 123-03
- COMPONENT CORROSION TEST
- BI 124-01
- FILIFORM CORROSION TEST
- BI 151-01
- Pencil Hardness of paint film
- BI 152-01
- RESISTANGE CF PAINT FILMS TC SCLVENTS
- BI 157-06
- HIGH PERFORMANCE STONE CHIP RESISTANCE TEST NEW RATING SCALE
- BI 160-01
- Florida and Arizona Outdoorexposure Test
- BI 161-01
- MAR RESISTANCE DETERMINATION FOR AUTOMOTIVE COATINGS
- BI 168-01
- FLUID RESISTANCE OF CHASSIS AND EXTERIOR MATERIALS FOR INCIDENTIAL EXPOSURE
- BN 103-01
- RESISTANCE OF COATED FABRICS AND PLASTIC FILM TO MIGRATION STAINING AND BLOCKING
- BN 107-01
- CROCKING TEST
- BN 108-02
- RESISTANCE TO ABRASION - TABER ABRASER
- BN 108-04
- Ristance to Scuffing
- BN 108-13
- RESISTANCE TO SCRATCHING
- BN 112-08
- SOILING & CLEANABILITY TEST FOR INTERIOR TRIM MATERIALS
- BN 121-01
- BOND STRENGTH Test -INTERIOR TRIM DECORATIONS
- BN 151-01
- Determation of 180 Degree peel adhesion strength of Laminates
- BN 155-01
- RESISTANCE TO SIMULATED FINGER TIP ABRASION
- BO 101-05
- DETERMINATION OF FUEL RESISTANCE OF PLASTIC PARTS
- BO 112-06
- Staining of trim Material indification Markings
- BO 115-01
- Platic- Ristance to artifical weather
- BO 116-01
- Exposure of Interior trim material in a controlled irradiance water colded xenon -arc apparatus
- BO 131-01
- Determination and assessiment of Odor from Interior trim Materials/ Components / Assiemblies
- BO 131-03
- INTERIOR ODOR TEST
- BO 151-01
- RESISTANCE TO LOW TEMPERATURE IMPACT
- BO 155-01
- PLASTICS AND TAPES RESISTANCE TO PROTECTIVE WAXES AND DEWAXING MATERIAL
- BO 160-04
- RESISTANCE OF PAINTED PLASTIC PARTS TO HIGH PRESSURE CLEANING OPERATIONS
- BO 162-01
- RESISTANCE TO SCRATCH AND MARR
- BP 153-01
- STAINING OF SURFACES BY POLYMERS AND ELASTOMERS
- BQ 104-07
- Envionmental Test cycle
- BQ 105-01
- COPPER-ACCELERATED ACETIC ACID-SALT SPRAY TESTING
- BZ 156-01
- DETERMINATION OF FORMALDEHYDE, ALDEHYDE, AND KETONE EMISSIONS FROM NON METALLIC COMPONENTS, PARTS AND MATERIALS IN THE VEHICLE INTERIOR
- BZ 157-01
- Determination of organic emissions from non-metallic materials in vehicle interiors by Headspace Gas Chromatography
- CETP 00.00-L-467
- Laboratory acclerated cyclic corrosion test
- DVM-0058-PA
- EXTERIOR CLEARCOAT - SCRATCH RESISTANCE ON RIGID SUBSTRATES
- ES_E90B_54043B13_AA
- SPECIAFICATION : MODULE ASSY DRIVER AIR BAG
- ES_F2DB_54044A74_AB
- SPECIAFICATION : MODULE ASSY PASS AIR BAG RESTRAINT TWR VEHICLE SAFETLY SYSTEM
- ESB-M70J5-A
- PAINT, POWDERED, THERMOSETTNG POLYESTER
- EU-BN 1-1
- Ristanceto of Materials to fade
- RDTM-069
- Ford filiform procedure
- RES.30.AR.105
- Mar Resistance
- RES.30.AR.175
- Abrasion Resistance of non metallic Material - Taber method
- SDS_CPSC 11.06.03
- Steering Wheel - Passive Restraints
- SSM-2P 9552-A
- energie and energie accessories
- WSB-M1P73-B2
- ernergieering material specification
- WSK-M15J4-A
- paint, two plastic, subtrates, interior
- WSK-M2P159-A
- PAINT PERFORMANCE, ALUMINUM ROAD WHEELS
- WSK-M32J125-A
- paint clear coat in base coat / clear coat system, baking ,exterior ,top coat
- WSK-M3G178-B1
- TAPE, DECORATIVE, PRESSURE SENSITIVE, EXTERIOR LOW UV, VERTICAL APPLICATIONS
- WSK-M3G178-B2
- TAPE, DECORATIVE, PRESSURE SENSITIVE, EXTERIOR , LOW UV, CHIP RESISTANT, VERITICAL APPLICATIONS
- WSK-M3G178-B3
- TAPE, DECORATIVE, PRESSURE SENSITIVE, EXTERIOR, HIGH UV, HORIZONTAL, GREENHOUSE APPLICATIONS
- WSK-M3G178-B4
- TAPE, DECORATIVE, PRESSURE SENSITIVE, EXTERIOR, HIGH UV, CHIP RESISTANT, HORIZONTAL, GREENHOUSE APPLICATIONS
- WSK-M98P6-A
- FINISHED PARTS, PLASTICS, EXTERIOR
- WSS-M15J13-A
- PAINT, TWO COMPONENT COLOR COAT FOR PLASTIC, Interior
- WSS-M15J15-A1
- SOFT TOUCH, STRAIGHT SHADE
- WSS-M15J15-A2
- SOFT TOUCH, metallic
- WSS-M15P34-B1
- Performence, Interior trims appliques, high wear
- WSS-M15P34-B2
- Performence, Interior trims appliques, low wear
- WSS-M15P34-E
- PERFORMANCE, INTERIOR TRIM COMPONENTS WITH APPLIQUES
- WSS-M15P4-F
- ASSEMBLY PERFORMANCE, HARD MOLD-IN-COLOR INTERIOR COMPONENTS
- WSS-M2P122-D2
- PAINT PERFORMANCE, ALUMINUM WHEELS, INTERIOR STOWED SPARE
- WSS-M2P122-D3
- PAINT PERFORMANCE, steel WHEELS, ROAD AND UNDERBODY SPARE
- WSS-M2P122-D4
- PAINT PERFORMANCE, steel WHEELS, INTERIOR STOWED SPARE
- WSS-M2P177-C1
- PAINT PERFORMANCE, METAL SUBSTRATES, LOW VISIBILITY, 4 WEEK RESISTANCE
- WSS-M2P177-C2
- PAINT PERFORMANCE, METAL SUBSTRATES, MODERATE VISIBILITY, 6 WEEK RESISTANCE
- WSS-M2P177-C3
- PAINT PERFORMANCE, METAL SUBSTRATES, HIGH VISIBILITY, 9 WEEK RESISTANCE
- WSS-M2P180-A
- PAINT PERFORMANCE, RIGID SUBSTRATES, EXTERIOR
- WSS-M2P180-C
- PAINT PERFORMANCE, RIGID SUBSTRATES, EXTERIOR
- WSS-M2P180-D
- PAINT PERFORMANCE, RIGID SUBSTRATES, EXTERIOR
- WSS-M2P185-A1
- PAINT PERFORMANCE, ENGINES, METALLIC SUBSTRATES, ALSO FOR ENGINE INTERIOR, MAX PERFORMANCE
- WSS-M2P185-A2
- PAINT PERFORMANCE, ENGINES, METALLIC SUBSTRATES, HIGH PERFORMANCE
- WSS-M2P185-A3
- PAINT PERFORMANCE, ENGINES, METALLIC SUBSTRATES, STANDARD PERFORMANCE
- WSS-M2P185-A4
- PAINT PERFORMANCE, ENGINES, METALLIC SUBSTRATES,MIN PERFORMANCE
- WSS-M2P185-A5
- PAINT PERFORMANCE, ENGINES, METALLIC SUBSTRATES, ALSO FOR ENGINE INTERIOR, MAX PERFORMANCE
- WSS-M2P185-A6
- PAINT PERFORMANCE, ENGINES, METALLIC SUBSTRATES, HIGH PERFORMANCE
- WSS-M2P185-A7
- PAINT PERFORMANCE, ENGINES, METALLIC SUBSTRATES, STANDARD PERFORMANCE
- WSS-M2P185-A8
- PAINT PERFORMANCE, ENGINES, METALLIC SUBSTRATES,MIN PERFORMANCE
- WSS-M2P188-A1
- PAINT PERFORMANCE, PLASTIC SUBSTRATES, INTERIOR
- WSS-M2P188-B1
- PAINT PERFORMANCE, PLASTIC SUBSTRATES, INTERIOR
- WSS-M2P190-A
- PAINT PERFORMANCE, INTERIOR PARTS METAL SUBSTRATES
- WSS-M33J7-B4
- tempory protective fail coating
- WSS-M33J7-B5
- tempory protective fail coating
- WSS-M4P13-A
- ANODIZED ALUMINUM PERFORMANCE, BRIGHT EXTERIOR TRIM
- WSS-M5P8-B1
- LIGHTING METALIZATION, PLASTIC SUBSTRATES
- WSS-M5P8-B2
- LIGHTING METALIZATION, Metal Substrates
- WSS-M99P2222 – B1
- PERFORMANCE, VEHICLE INTERIOR ENVIRONMENT QUALITY MATERIAL / COMPONENT REQUIREMENTS
- WSS-M99P2222 – B2
- PERFORMANCE, VEHICLE INTERIOR ENVIRONMENT QUALITY ALLERGY TESTING AND DIRECT SKIN CONTACT REQUIREMENTS
- WSS-M99P2222 – B3
- PERFORMANCE, VEHICLE INTERIOR ENVIRONMENT QUALITY HVAC REQUIREMENTS
- WSS-M99P2222 – B4
- PERFORMANCE, VEHICLE INTERIOR ENVIRONMENT QUALITY COMPLETE VEHICLE REQUIREMENTS
- WSS-M99P32-D2
- PERFORMANCE, ACCOUSTICAL WHEEL ARCH/WELL LINERS
- WSS-M99P32-D3
- PERFORMANCE, ACCOUSTICAL HEAVY DUTY WHEEL ARCH/WELL LINERS
- WSS-M99P32-D4
- PERFORMANCE, ACCOUSTICAL UNDERBODY/ENGINE SHIELDS
- WSS-M99P32-D5
- PERFORMANCE, ACCOUSTICAL HEAVY DUTY UNDERBODY/ENGINE SHIELDS
- WSS-M99P9999-A1
- RESTRICTED SUBSTANCE MANAGEMENT STANDARD
GM
- 09 272 502
- Performence Requirements for painted CNG- Tanks
- ESJ05-Z-38
- ENGERIEERING SPECIFICATION OF PAINTIN FOR OPEL DRIVE SHAFT
- GM 4465P
- Water fog humidity Test
- GM 6121M
- GM Energieering standards
- GM 9252
- THERMAL SHOCK FOR PAINT ADHESION
- GM 9509P
- Resistance of coatings to chemical etching and distortion
- GM 9511P
- SCAB CORROSION CREEPBACKOG PAINT SYSTEM ON METAL SUBSTRATES
- GM 9531P
- Water Jet Tests
- GM 9540P
- Accelerated Corrosion Test
- GM 9682P
- FILIFORM CORROSIONS TEST PROCEDURE FOR PAINTED ALUMINIUM WHEELS AND PAINTED ALUMINIUM WHEEL TRIM
- GM 9904P
- MULTI AXIAL IMPACT TEST
- GM 9984164
- Material SPECIFICATION PAINT
- GM QT 010301
- TECH: LIEFERBEDINGUNGEN PRÜFVORSCHRIFT
- GM QT 010301-03
- TECH: LIEFERBEDINGUNGEN PRÜFVORSCHRIFT
- GM TM 228700
- Material SPECIFICATION BODY EQUITMENT
- GME 00002
- General Requirements for coloured Plastic Components for Exterior
- GME 00006
- Minimun Performens Requirements for Decorative Chromium plated plastic parts
- GME 00007
- Performance requirements for applied organic finishes go Interior and ExteriorAutomotive plastic parts and components
- GME 00010
- Performance requirements for applied organic finishes go Interior and ExteriorAutomotive plastic parts and components
- GME 00200
- Organic coat finish for wheels (steel and light alloy wheels)
- GME 00211
- Performence Requirements for applied paint finish on platic parts and components for interior use
- GME 00251
- electrolytically deposited Multi coat systems
- GME 00252
- electrolytically deposited coat of zinc. Zinc-nickel-alloy,tin,lead ,cooperon iron and steel, and of lead in tin on cooper
- GME 00252
- Electrolytically Deposited Metallic Coatings
- GME 00256
- Coating based on Zinc, Alumiunm and Chromium
- GME 00257
- organic coat finish for cast iron parts
- GME 13003
- Passenger car - heating- ventilation and air conditioning Part 11, Refrigerant Lines
- GME 60202
- Determination of the Resistance of Automotive Components to High Humidity Environments
- GME 60203
- Determination of the Resistance to Corrosion of Organic Coatings under Cyclic Alternating Conditions
- GME 60206
- Determination of the Resistance to Corrosion of Automobile components by salt spray fog testing
- GME 60207
- Determination of the Resistance to Corrosion of Automobile components by cooper acid salt spray
- GME 60213
- Determination of Resistance to Corrosion of Aluminum Radiators by Sea Water Acetic Acid Test (SWAAT)
- GME 60265
- Determination of the Resistance to Fuel of Automobile exterior trim component
- GME 60268
- Determination of Resistance to Stone Impact of Sudace Coatings, Plastics and Self Adhesive Films
- GME 60269
- Test method of determining the abrasion resistance of metallised , painted, printed etc. platic parts
- GME 60275
- Determination of the Resistance to synthetic perspiration salution of Automobile trim component
- GME 60276
- Test method of determining resistance to Odour propagation of trim materials
- GME 60292
- Determination of colour fastness and resistance to aritificial light
- GME 60365
- TEST METHODE FOR EVALUATING FOGGING CHARACTERISTICS TRIM MATERIALS
- GME 60400
- Test Method for Determining the Resistance to Abrasion of Organic Coatings
- GME 60401
- Cross Hatch Test of Organic Coatings
- GME 60402
- Determining the Scratch Resistance of Organic Coating
- GME 60403
- Resistance of Organic Coatings to Colour Change by Fuel OIL SOOT
- GME 60404
- Resistance of Organic Coatings to Surface Deterioration by chemical astion
- GME 60405
- Test method for Determining the impact- saline solution resistance of organic coatings
- GME 60406
- Resistanceof organic coatings , platic and adhared films to surface deterieration by anti freeze solation
- GME 60407
- Test Method for Determining-the Impact Resistance of Organic Coatings
- GME 60412
- Orange peel evaluation of painted surfaces
- GME L 0001
- Test Fluid
- GME L 0003
- Methanol modified test fluid
- GMI 60206-1
- GM INTERNATION ENGERIEERING STANDARD
- GMI 60266
- Determination of Resistance to Cleaning Agents of Automotive Trim Components
- GMW 15201
- Double Coated Foam Tape for Exterior Attachment
- GMW 14124
- automotive environmental cycles
- GMW 14192
- Condenser with Intergrated receiver dryer prodruct and test procedure specification
- GMW 14333
- Resistance to Fuels of Exteriors Automotive Materials and Components
- GMW 14334
- chemical resistance to fluid
- GMW 14444
- Material Related Interior Part Performance
- GMW 14445
- Sunscreen and Insect Repellent Resistance
- GMW 14458
- Procedure for Copper-Accelerated Acetic Acid Salt Spray (CASS) Test
- GMW 14650
- Performance requirements for exterior plastic parts
- GMW 14665
- Anodic Oxidation Coating on Aluminum
- GMW 14668
- Minimum Performance Requirements for Decorative Chromium Plated Plastic Parts
- GMW 14669
- Organic Coating Performance for Exterior and Interior Metallic Components
- GMW 14671
- Organic Coating Performance for underhood and underbody Components
- GMW 14674
- organic coatings for cast iron parts
- GMW 14698
- scratch resistance of organic coatings and self ashesive foils
- GMW 14700
- Stone Impact Resistance of Coatings
- GMW 14701
- Resistance of coatings to chemical etching and distortion
- GMW 14729
- Procedures for High Humidity Test
- GMW 14797
- Painted Plastic Parts Performance Requirements
- GMW 14829
- tape adhesion test for paint finishes
- GMW 14864
- produce for determining the staining of trim materials due to sulfur ,SO2, and hydrogen sulfid, H2S
- GMW 14867
- Performance Requirements of Paints on Interior Plastic Substrates
- GMW 14872
- Cyclic Corrosion Laboratory Test
- GMW 14885
- Painted Aluminum Road Wheels - Paint Performance Requirements
- GMW 14914
- Test fluids to fuel resistant test
- GMW 15272
- Corrosions perfomance specification
- GMW 15282
- Corrosions/undercutting scribe creepback
- GMW 15287
- Filiform Corrosion Test Procedure for Painted Aluminum Wheels and Painted Aluminum Wheel Trim
- GMW 15356
- SHEET MATAL RATING SCALE
- GMW 15357
- COMPONENT RATING SCALE
- GMW 15358
- FASTNER RATING SCALE
- GMW 15359
- WHITE CORROSIONS RATING SCALE GUIDELINE
- GMW 15487
- DETERMINING RESISTANCE TO ABRASION OF ORGANIC COATINGS
- GMW 15635
- Determination of aldehyde and ketone emissions from interior materials
- GMW 15777
- Vehicle Exterior and Add-On Parts Paint Appearance Requirements
- GMW 15891
- SOLVENT RUB METHOD DETERMINING CURE OF PAINTED METAL OR PLASTIC SUBSTRATES
- GMW 16073
- engine oil humidity corrosions Test
- GMW 16225
- Acoustic Wheel House Liner Materials
- GMW 16423
- DECORATIVE EXTERIOR DECALS - FOILS
- GMW 16745
- Water Jet Tests
- GMW 3172
- General Specification for Electrical/Electronic Component Analytical/Development/Validation (A/D/V) Procedures for Conformance to Vehicle Environmental, Reliability, and Performance Requirements
- GMW 3205
- Test method for determining resistance to Odor Propagation of Interior materials
- GMW 3208
- Rotary Abrasion Test, Taber Test
- GMW 3221
- Standard conditioning of organinc materials
- GMW 3235
- Fogging characteristics of trim materials
- GMW 3286
- Neutral Salt Spray (NSS) Test
Honda
- 3967Z-XXXX-G200
- S P E C , P A R K I N G S E N S O R T E S T S T D
- ES25310-04
- Al-Radiator Ass`y
- ES97606-01
- Test specification for A/CON. Condenser Assembly
- HES_D2016-07
- General Coatings (on metalls )
- HES_D6501-06
- General Methods for Coatings
- spec 4271Z-SNA-A001
- Spec, AL surface treatment
- spec 4272Z-S6M-0000
- Material Spec, wheel disk AL
IEC, DIN IEC
- DIN IEC 60093
- Measurement of the electrical resistance through a material (vertical resistance)
- IEC 61340-2-1
- Electrostatics - Part 2-1: Measurement methods - Ability of materials and products to dissipate static electric charge
- IEC 61340-3
- Electrostatic behaviour
ISO, DIN ISO
- ISO 11503
- Paints and varnishes - Determination of resistance to humidity (intermittent condensation)
- DIN ISO 16000-3
- Indoor air - Part 5: Sampling strategy for volatile organic compounds (VOCs)
- DIN ISO 16000-6
- Indoor air - Part 6: Determination of volatile organic compounds in indoor and test chamber air by active sampling on Tenax TA® sorbent, thermal desorption and gas chromatography using MS or MS-FID
- DIN ISO 18314-1
- Analytical colorimetry - Part 1: Practical colour measurement
- DIN ISO 18314-2
- Analytical colorimetry - Part 2: Saunderson correction, solutions of the Kubelka-Munk equation, tinting strength, hiding power
- DIN ISO 18314-3
- Analytical colorimetry - Part 3: Special indices
- DIN ISO 1409
- Polymer dispersions and rubber latices (natural and sythetic) - Determination of surface tension by the ring method
- DIN ISO 4532
- Determination of the resistance of enamelled articles to impact - Pistol test
- ISO 11359-2
- Thermomechanical analysis (TMA) - Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature
- ISO 13837:2008
- Road vehicles - Safety glazing materials - Method for the determination of solar transmittance
- ISO 15989
- Plastics - Film and sheeting - Measurement of water-contact angle of corona-treated films
- ISO 20340
- Performance requirements for protective paint systems for offshore and related structures
- ISO 2878
- Determination of electrical resistance
- ISO 6383-1
- Determination of tear resistance - Part 1: Trouser tear method
- ISO 6452
- Rubber- or plastics-coated fabrics - Determination of fogging characteristics of trim materials in the interior of automobiles
- ISO 6721-1
- Determination of dynamic mechanical properties - Part 1: General principles
- ISO 6721-11
- Determination of dynamic mechanical properties - Part 11: Glass transition temperature
- ISO 6721-12
- Determination of dynamic mechanical properties - Part 12: Compressive vibration - Non-resonance method
- ISO 6721-4
- Determination of dynamic mechanical properties - Part 4: Tensile vibration - Non-resonance method
- ISO 6721-5
- Determination of dynamic mechanical properties - Part 5: Flexural vibration - Non-resonance method
- ISO 760
- Determination of water - Karl Fischer method
- ISO 8690
- Decontamination of radioactively contaminated surfaces
- ISO 9050:2003
- Determination of light/solar direct/total solar energy/ultraviolet transmittance and related glazing factors
- ISO/DIS 4630-2
- one-dimensional colour index (such as Pt-Co, APHA-, Hazen-, Iodine- and Gardner-colour index)
- ISO/DIS 6271
- one-dimensional colour index (such as Pt-Co, APHA-, Hazen-, Iodine- and Gardner-colour index)
- ISO/PDTS 19392-3
- Coating systems for wind-turbine rotor blades - Part 3: Determination and evaluation of resistance to rain erosion using water jet
Jaguar
- ES_XR831007DC
- Painted Cast Aluminiumroad wheels
- JNS-30.04.10
- Test of Mar resistance
- JNS-30.04.10
- Test of Mar resistance
- TPJLR.52.002
- Mar Resistance
- TPJLR.52.004
- Resistance to Scratch
- TPJLR.52.058
- Adhesive Bond Strength – 90 Degree and 180 Degree Peel Method
- TPJLR.52.061
- Paint Adhesion Test Method
- TPJLR.52.153
- Interior Painted Trim Resistance to Suncream
- TPJLR.52.155
- Fluid Spotting of Automotive Trim
- TPJLR.52.156
- Resistance of Interior Trim to Perspiration – Immersion Test
- TPJLR.52.160
- Resistance to Exterior Transit Protection Materials
- TPJLR.52.210
- CLEANABILITY TEST FOR INTERIOR TRIM Materials
- TPJLR.52.252
- Resistance To Neutral Salt Spray Corrosion Test
- TPJLR.52.253
- Test Cycle for Resistance to Humidity and Salt Spray
- TPJLR.52.254
- Calcium Chloride Accelerated Corrosion Test (Russian Mud Test)
- TPJLR.52.351
- Resistance to Humidity - General
- TPJLR.52.352
- Resistance to Heat Ageing - General
- TPJLR.52.353
- Accelerated Environmental Ageing
- TPJLR.52.423
- Determination of Surface Fibre Deterioration
- TPJLR.52.456
- Scrape Adhesion of Organic Coatings
- TPJLR.52.458
- Determination and assessment of odour from interior trim materials, components and assemblies
- TPJLR.52.551
- Discoloration of Organic or Decorative Finishes and Trim Materials by Dry Heat
- TPJLR.52.552
- Discoloration of Organic and Decorative Finishes and Trim Materials by Extraction Staining
- TPJLR.52.554
- Prohesion Corrosion Testing
- TPJLR.52.561
- Resistance Of Painted Exterior Parts To High Pressure Cleaning Operations
- TPJLR.52.564
- Water Immersion Test For Painted Parts And Panels
- TPJLR.52.599
- High Performance Stone Chip Resistance Test
- TPJLR.52.656
- Hydrolysis Test - Interior Painted Finishes
- TPJLR.52.701
- Determination of Crack Density of Microcracked or Pore Density of Micro-porous Chromium
John Deere
- JDQ 116
- Mandrel Bend (Conical)
- JDQ 117
- Prüfung der Stoßfestigkeit von Lackschichte
- JDQ 159
- Cyclic Corrosion Test for Corrosion Resistance of Paint Films
KIA
- ES25310-04
- Al-Radiator Ass`y
- ES97606-01
- Test specification for A/CON. Condenser Assembly
MAN
- AN 400 Teil 2
- Korrosionsschutz bei Kaufteilen
- M 3005-1
- Gebogene Rohre
- M 3007
- Prüfung der Fleckenentfernbarkeit an matten Beschichtungen
- M 3018
- Corrosion protection and coating systems for purchased parts, Truck and Bus
- M 3022
- Beschichtungsstoffe für Bauteile aus Kunststoff
- M 3023
- Bestimmung der Schwefeldioxidbeständigkeit von Beschichtungen
- M 3082
- Korrosionsschutzwachse
- M 3150-1
- Oberflächengüte
- M 3150-2
- Oberflächengüte
- M 3150-3
- Oberflächengüte
- M 3150-4
- Oberflächengüte
- M 3150-5
- Oberflächengüte
- M 3150-6
- Oberflächengüte
- M 3166
- Pulverbeschichtung
- M 3171
- Testing the stone impact resistance (Venturi principle)
- M 3299
- Kugelfall Prüfung
- M 3497
- Beschichtete und bedruckte Bauteile ausKunststoff im Fahrzeuginnenraum
- MAN 183-1
- Korrosionsschutz und Oberflächenschutzsysteme für Bus und LKW
- Man 272
- Korrosionsschutz von Behältern und Rohrverschraubungen aus Stahl im Druckluftsystem
- MAN 277
- Haftungsprüfung (Kratzprüfung)
- MAN 352
- Prüfung der Medienbeständigkeit
- MAN 365-1
- MAN-Bewitterungssimulationstest
- MAN 365-2
- MAN-Korrosionsfahrtest
Mercedes Benz
- MBN 10305-1
- E/E Environmental Testing Part 1: Test Specifications
- MBN 10473-1
- Messung von Farben
- MBN 10473-2
- Technische Daten zur Farbmessung
- MBN 10476
- Visuelle Farbbeurteilung von lackierten Karosserien, Anbauteilen und Blechen im Exterieur
- MBN 10494-1
- Part 1: General Requirements
- MBN 10494-10
- Paint Test Methods –Part 10: Special Test Methods for Electrodeposition Coats in Dry Condition
- MBN 10494-2
- Part 2: Testing of Paints in Wet Condition
- MBN 10494-3
- Paint Test Methods – Part 3: Processing Tests
- MBN 10494-4
- Paint Test Methods –Part 4: Optical Tests
- MBN 10494-5
- Paint Test Methods –Part 5: Technical-Mechanical Tests
- MBN 10494-6
- Paint Test Methods –Part 6: Climatic Tests
- MBN 10494-7
- Paint Test Methods –Part 7: Resistance to Chemicals, Test Mixtures and Test Concentrates
- MBN 10494-8
- Paint Test Methods – Part 8: Adhesion of Adhesives on the Coating
- MBN 10494-9
- Paint Test Methods – Part 9: Special Test Methods for Electrodeposition
- MBN 10526
- Prüfmethoden für selbstklebende Bauteile
- MBN LV 124-2
- Electric and Electronic Components in Motor Vehicles up to 3,5t – General Requirements, Test Conditions and Tests Part 2: Environmental Requirements
Nissan
- 28401NDS01
- BASIC PHYSICOCHEMICAL ENVIRONMENTAL SPECIFICATIONS of Electronic Parts
- NDS 21410
- RAD ASSY
- NDS 92111_EN
- CORROSION TEST METHOD OF ASSESSING ALUMINUM HEAT EXCHANGERS
- NES M0007
- Testing method for automotive paint
- NES M0138
- Methods of CASS Testing
- NES M0140
- Salt Spray Testing
- NES M0141
- Abrasion resistance to RCA method according
- NES M0158
- Methods of Compound Corrosions Test
- NES M0159
- Testing Method of the Scratch Resistance of Interior Polypropylene Resin Parts
- NES M4063
- Decorative Chormium Plating
- NES M5055
- Brake Fluid, Non-Petroleum Base – Automotive
- NES M5083
- Rust Preventive Coating Materials for Automobile Parts
- NES METHODS OF TEST
- Methods of Test for Coating of synthetic resin
- NES SALT SPRAY TESTING
- Salt Spray Testing
Porsche
- PLB-4-K1-Kunststoffmulden-PO623-ÄSt1
- Leistungsbeschreibung individueller Teil
- PN 710
- Prüfmedien - Werkstoffverträglichkeit
- PN 780
- Emissionsverhalten
- PN 790
- Verdunstungsemission - SHED
- PPV 4008
- Lacke und lackierte Teile
- PPV 4017
- Korrosionsprüfung - Modifizierter Klimawechseltest
- PPV 4022
- Begrenzung von Oberflächenfehlern an Interieur- Bauteilen
- PPV 4050
- Bestimmung flüchtiger, organischer Emissionenaus nicht kraftstoffbeaufschlagten Bauteilen; Emissionsmessung in SHED-Kammern
- PPV 7000
- Schälversuch
- PPV 7050
- Gesamtfahrzeug Medienbeständigkeit von Kunststoffen und thermoplastischen Elastomeren in Verbindung mit mechanischen Spannungen
- PTL 10105
- Exterieur ; Alterungsverhalten durch künstliche Bewitterung ; Anforderung und Prüfung
- PTL 14062
- Schläuche für Scheibenwischeranlagen ; Anforderung und Prüfung
- PTL 4025
- Interieur / Exterieur - Oberflächendekore ; Kunststoffbauteile mit elektrolytisch abgeschiedener Metalloberfläche ; Anforderung und Prüfung
- PTL 4044
- Klebeband ; Acryl-Schaumband, beidseitig selbstkebend
- PTL 4061
- Karosserie ; Gleitlackbeschichtete Karosseriedichtungen ; Anforderung und Prüfung
- PTL 5522
- Lackierung nichtmetallischer Werkstoffe für Innenausstattung
- PTL 5524
- Lackierung ; Karosserie-Außenhaut-Teile aus flexiblen Kunststoffen ; Anforderung und Prüfung
- PTL 5525
- Lackierung ; Karosserie-Außenhaut-Teile aus harten Kunststoffen (Thermo- und Duroplaste) ; Anforderung und Prüfung
- PTL 5529
- Lackierung von Karosserie-Aussenhaut-Teilen aus metallischen Werkstoffen ; Anforderung und Prüfung
- PTL 5536
- Interieur ; Oberflächendekore - Lackierung/ Tampondruck/ Heißprägung ; Anforderung und Prüfung
- PTL 5538
- Interieur ; Oberflächendekore - Holz/ Carbon/ Klavierlack/ Metalle ; Anforderung und Prüfung
- PTL 7515
- Oberflächenschutz ; Oberflächenbeschichtung von metallischen Exterieur Bauteilen ; Anforderung und Prüfung
- PTL 7518
- Oberflächenschutz ; Lackierung / Pulverbeschichtung metallischer Fahrzeugteile (Oberflächen x301, x601, x602, x603, x604, x651) ; Anforderung und Prüfung
- PTL 7520
- Exterior / Oberflächenschutz ; Pulverlackierung- Oberflächex652 ; Anforderung und Prüfung
- PTL 7524
- Oberflächenschutz ; Anodisches Oxidieren - Eloxalschichten (w625, w630, w640) ; Anforderung und Prüfung
- PTL 8140
- Interieur ; Allgemeine Anforderungen an Bauteile und Halbzeugmaterialien ; Anforderung und Prüfung
- PTL 8501
- Interieur ; Brennverhalten ; Anforderung und Prüfung
Renault (PSA)
- 47 - 01 - 002 / - - M
- ELECTROPLATING DECORATIVE COATING - CHROME PLATING ON PLASTIC PARTS
- 47 - 03 - 005 / - - E
- PAINT COATINGS AND FOILS BY DIPPING FOR INTERNAL PLASTIC PARTS
- D10 5495
- Test for interior materials vehicle - Evaluation of the amount of volatile organic compounds (VOCs) by thermodesorptions/GS/MS
- D11 1054 / - - D
- SUPPLENESS OF A PIECE BY IMPRESSION OF A HEMISPHERICAL PUNCH BEADS, PROTECTIVE STRIPS, ARMRESTS, VARIOUS TRIMMING
- D14 1055 / - - F
- MATERIALS AND ORGANIC COATINGS WEAR BY RUBBING
- D15 1343 / - - E
- COLOURED MATERIALS VISUAL COMPARISON OF COLOURS IN LIGHT CHAMBER
- D17 1736 / - - C
- PAINTS AND PLASTICS COLOUR VARIATION TEST USING COLORIMETER
- D17 2028 / - - C
- CORROSION TEST BY AUTOMATIC CHANGE OF PHASES OF SALT SPRAY, DRYING AND HUMIDITY (ECC1)
- D17 2028 / - - D
- CORROSION TEST BY AUTOMATIC CHANGE OF PHASES OF SALT SPRAY, DRYING AND HUMIDITY (ECC1)
- D17 2028/--B
- Corrosions Test by automatic phase change salt spray humidity and drying
- D17 3021 / - - C
- CORROSION TEST BY AUTOMATIC CHANGE OF PHASES OF SALT SPRAY, DRYING AND HUMIDITY (ECC1)
- D24 1702 / - - J
- PEINTURES RESISTANCE AU GRAVILLONNAGE PAR PROJECTION DE GRENAILLE
- D24 1702/--J
- PAINTS RESISTENCE TO GRITTING BY SHOT BLASTING
- D25 1413 / - - C
- PAINT COATINGS, PLASTICS AND RUBBERS GLOSS MEASUREMENT
- D27 1740 / - - B
- Coatings of Paints action of organic liquids
- D27 1740 / - - C
- REVETEMENTS DE PEINTURE ACTION DES LIQUIDES ORGANIQUES
- D27 1740/--A
- Coatings of Paints action of organic liquids
- D27 1911 / - - D
- RUBBER AND PLASTIC PAINT COATINGS ARTIFICIAL AGEING USING WEATHEROMETER
- D33 1715 / - - C
- WHEELS AND WHEEL CAPS IN COATED LIGHT ALLOY CYCLIC CORROSION
- D33 1715 / - - F
- ROUES ET ENJOLIVEURS EN ALLIAGE LEGER REVETU ESSAI DE CORROSION CYCLIQUE
- D40 3004 / - - A
- Analysis of formaldehyde and other carbonyl compounds
- D42 1775 / - - C
- INTERIOR AND EXTERIOR PLASTIC PARTS RESISTANCE TO SCORING BY ABRASION
- D42 2036 / - - C
- PIECES EXTERIEURES PEINTES RESISTANCE A LA RAYURE PAR ABRASION
- D42 3109 / - - B
- Vehicle passenger compartment materials evaluation of the quantity of volatile organic compounds (VOC) by thermal desorption/GC/MS (FID)
- D44 1900 / - - C
- PLASTICS - RESISTANCE TO MARKING (RESISTANCE TO SCORING THROUGH POLISHING)
- D45 1727 / - - G
- Interior trim materials and passenger compartment parts - Fogging
- D47 1279 / - - G
- PLASTIC AND RUBBER PARTS RESISTANCE TO BODYWORK CONDITIONING AND DECONDITIONING PRODUCTS
- D47 1915 / - - C
- PLASTIQUES SOLIDITE DE LA TEINTE AUX FLUIDES SOUS L'ACTION DE LA LUMIERE
- D49 3001 / - - E
- Odour emissions, internal equipment parts - Intensity evaluation and global odour characterisation
- D49 3091 / - - A
- TENUE AU BLANCHIMENT A L'EAU SAVONNEUSE CHAUDE DES PIÈCES EN MATÉRIAUX STYRÉNIQUE POUR EXTÉRIEUR
- D57 1767 / - - C
- PAINTS RESISTANCE TO BIRD DROPPINGS
- ESJ01-Z-21
- ENGINEERING SPECIFICATION OF PAINT FOR NCV 2 DRIVESHAFT
Others
- ANSI Z80.3-1986
- NIR-Parameter
- ANSI Z87.1-2010
- NIR-Parameter
- AS 1067.1-1990
- NIR-Parameter
- CIE 1982
- Weißgrad
- EN 1836
- NIR-Parameter
- FINAT
- Schälversuche
- GANZ
- Weißgrad
- JIST 8141-1980
- NIR-Parameter
- RoHS-RL
- Schwermetalle
- SAE J 1756
- Determination of the fogging characteristics of interior automotive materials
- SAE J 1960
- Accelerated exposure of automotive exterior materials using a controlled irradiance water-cooled Xenon arc apparatus
- SAE J 2334
- Laboratory cyclic corrosion test
- SAE J 2527
- Performance based standard for accelerated exposure of automotive exterior materials using a controlled irradiance Xenon-arc apparatus
- SAE J 2635
- Filiform corrosion test procedure for painted aluminum wheels and painted aluminum wheel trim
Toyota
- BSDH1501
- Test method for print resistance of paint film
- BSDH1503
- Test method for adhesive property of paint film
- BSDH1504
- Test method for flexibility of paint film
- BSDH1508
- Test method for volatile solvent resistance of paint film
- BSDH1509
- Test method for chemical resistance of paint film
- BSDH1513
- Test method for color fading of paint film
- BSDH1519
- TEST METHOD FOR GLOSS OF PAINT FILM
- BSDH1539
- Test method for HARDNESS OF HARDNESS OF paint film
- BSDH1544
- Test method for nail scratch resistance on paint film
- BSDH1562
- Grease staining resistance test method for interior parts paint
- BSDH3130
- Paint quality for interior parts
- BSDL0601
- criteria for test of quality of colour change by aging
- BSDL2105
- Standard test methods for seat fabrics with regard to items concerning strength and durability
- BSDM0500
- Flammability test method for interior materials
- BSDM0503
- Fogging test method for non-metallic materials
- BSDM0505
- Smell qualitiy of non-metallic materials
- BSDZ0001
- RESTRICTIONS ON THE USE OF SUBSTANCE OF ENVIRONMENTAL AS MATERIALS OF PRODUCT COMPONENTS
- BSDZ0001
- RESTRICTIONS ON THE USE OF SUBSTANCE OF ENVIRONMENTAL AS MATERIALS OF PRODUCT COMPONENTS
- ESJ14-Z-134
- PAINT SPECIFIKATION OF UC SHAFT FOR TOYOTA MOTOR EUROPE
- JIS Z 2371
- Methods of salt spray test
- PPS_TEST_METHOD_1001
- COATED AND UNCOATED METAL PARTS AND FASTENERS
- PPS_TEST_METHOD_1002
- PAINT PRODUCTS
- PPS_TEST_METHOD_1016
- EXTERIOR PRODUCTS
- PPS_TEST_METHOD_2014
- ---
- PPS_TEST_METHOD_2018
- ALLOY WHEELS
- PPS_TEST_METHOD_4002
- PAINTED PRODUCTS
- PPS_TEST_METHOD_4005
- EXTERIOR PRODUCTS
- TSH1501G
- Test method for print resistance on paint film
- TSH1502G
- Test method for rub resistance on paint film
- TSH1503G
- Test method for adhesitiv resistance on paint film
- TSH1504G
- Test method for flexibility resistance on paint film
- TSH1505G
- Test method for water resistance on paint film
- TSH1507G
- Test method for heat resistance on paint film
- TSH1508G
- Test method for volatile solvent resistance on paint film
- TSH1509G
- Test method for chemical resistance on paint film
- TSH1511G
- Test method for thermal cycle resistance on paint film
- TSH1518G
- Test method for color measurment on paint film
- TSH1519G
- Test method for gloss on paint film
- TSH1520G
- Test method for light transmittance on paint film
- TSH1539G
- Test method for hardness on paint film
- TSH1551G
- Test method for electrodeposition on paint film
- TSH1552G
- Test method for salt spray
- TSH1553G
- Test method for chip resistance on paint film
- TSH1554G
- Test method for filiform coroosions resistance ( Toyota arrow chip test )
- TSH1555G
- Test method for accelerated corrosion under complex environment
- TSH1581G
- Test method for outdoor weather resistance on paint film
- TSH1582G
- Carbon arc Lamp type Test method for accelerated weathering resistance on paint film
- TSH1585G
- Xenon arc Lamp type Test method for accelerated weathering resistance on paint film
- TSH3122G
- Coating quality for aluminium wheel disk
- TSH3130G
- paint quality for interior parts
- TSH3131G
- paint film quality for exterior parts
- TSH6504G
- electroplated chromium coatings for decorations
- TSH7702G
- ZINC -COMPOSITE SILICON BASED RESIN COATING (HEXAVALENT CHROME-FREE)
- TSL2105G
- Standard test methods for seat fabrics :With regard to items :concerning strength and durability
- TSM0502
- General test method regarding materialproperties for plastic parts
- TSM0503G
- Fogging test method for non metallic materials method B
- TSM0505G
- Smell quality of non-metallic materials
- TSZ001G
- Control method for substance of environmental concern
- TSZ6005
- Indication method of material marking for plastic parts and rubber parts
VDA, VDE, VDI, VdL
- VDA 230-102
- Klimawechseltest
- VDA 233-102
- Zyklische Korrosionsprüfung von Werkstoffen und Bauteilen im Automobilbau
- VDA 270
- Bestimmung des Geruchsverhaltens von Werkstoffen der Kraftfahrzeug-Innenausstattung
- VDA 275
- Formaldehyde emission
- VDA 277
- Analysis of volatile contaminants from polymers
- VDA 278
- Thermal Desorption Analysis of Organic Emissions for the Characterization of Non-Metallic Materials for Automobiles
- VDA 621-181
- Compatibility of oils
- VDA 621-186
- Determination of electrical conductivity
- VDA 621-188
- Sedimentation an waagerechten Flächen (L-Effekt)
- VDA 621-192
- Abscheidespannung
- VDA 621-199
- Umgriff
- VDE 0300-2-1
- Electrical resistance
- VDE 0300-3
- Electrical resistance
- VDE 0303-21
- Elektrische Durchschlagfestigkeit
- VDI 3862 Blatt 3
- Messen gasförmiger Emissionen - Messen aliphatischer und aromatischer Aldehyde und Ketone nach dem DNPH-Verfahren - Kartuschen-Methode
- VdL-RL 03
- Formaldehyd (auch in trüben Systemen)
VW
- PV 1015
- Specific Volume Resistance Testing
- PV 1058
- Determination of the Micro-Crack Pattern on Chrome-Plated Surfaces
- PV 1063
- Determination of Micropore Density
- PV 1065
- Determination of Potential Differences and Layer Thicknesses of Nickel Coatings
- PV 1073
- Corrosion Resistance of Chrome Surfaces
- PV 1200
- Testing of Resistance to Environmental Cycle Test (+80/-40) °C
- PV 1208
- Corrosion Test (SWAAT)
- PV 1209
- Corrosion Test (Environmental Corrosion Cycle Test)
- PV 1210
- Corrosion Test
- PV 1217
- Stone chip resistance
- PV 1303
- Xenon Arc Light Aging of Vehicle Interior Components
- PV 1306
- Exposure Test for Determining the Tackiness of Polypropylene Parts
- PV 1323
- Testing of Corrosion Protection Behavior
- PV 1401
- Corrosivity Testing
- PV 1425
- Testing the Corrosion Protection Behavior of Engine Oils When Ethanol,
- PV 1492
- Acetic Acid, and Water Are Added
- PV 1502
- Testing for Resistance to Cracking
- PV 1503
- Pressure Washer Test
- PV 20.01
- Determination of wetting capability
- PV 2005
- Testing of Resistance to Environmental Cycle Test
- PV 2034
- Floating Roller Peel Test
- PV 2037
- Resistance to preservatives and Cleaning agents
- PV 2052
- Leak Tightness of Hem-Flange Bonds
- PV 3.1.7
- Recording the IR Spectrum of Electro-Dip Paints
- PV 3.10.3
- Test of resistance to caustic solutions
- PV 3.10.5
- Testing of Resistance to Industrial Grade Dust Removers
- PV 3.10.7
- Testing for Substances That Impair Paint Wetting Ability
- PV 3.14.4
- Mobile Testing of the Stone-Chip Resistance of Body Top Coats
- PV 3.14.7
- Test of Stone-Chip Resistance according to DIN EN ISO 20567-1
- PV 3.15.3
- Prüfung der Korrosionsbeständigkeit nach KTL-Beschichtung auf verzinktem Stahlblech
- PV 3.15.3
- Prüfung der Korrosionsbeständigkeit nach KTL-Beschichtung auf verzinkten Stahlblech
- PV 3.16.4
- Testing of Acid Resistance
- PV 3.17.1
- Determination of Corrosion Resistance after Mechanical Damage
- PV 3.3.3.
- Scratch Resistance Testing of Clear Coats
- PV 3015
- Determining Condensable Constituents (G)
- PV 3226
- Residual Loosening Torque Measurement on the Revolving Test Bed
- PV 3227
- Vorspannkraft und Drehmomentmessung
- PV 3228
- Bremsrohrverschraubung
- PV 3336
- Checking for Impurities
- PV 3341
- Determination of emission of organic compounds
- PV 3356
- Soiling and Cleaning Behavior
- PV 3516
- Leak Tightness Test
- PV 3900
- Odor Test
- PV 3903
- Measurement of Bending Stiffness
- PV 3905
- Ball Drop Test
- PV 3906
- Testing of Abrasion Behavior
- PV 3914
- Abrasion resistance with a heel
- PV 3925
- Polymer Materials; Measuring Emissions of Formaldehyde
- PV 3929
- Non-Metallic Materials; Weathering in Dry, Hot Climate (Exterior)
- PV 3930
- Non-Metallic Materials; Weathering in Humid, Hot Climate (Exterior)
- PV 3952
- Scratch Resistance Test
- PV 3964
- Testing of Cream Resistance
- PV 3965
- Visual Color Matching according to DIN EN ISO 3668
- PV 3966
- Stress Whitening Properties (Ball Drop Test)
- PV 3974
- Determination of the Mar Resistance of Precision-Molded Grained Surfaces in the Vehicle Interior
- PV 3975
- Scrub Resistance of High-Gloss Surfaces in the Vehicle Interior
- PV 3983
- Medienbeständigkeit von Kunststoffen und thermoplastische Elastomere inVerbindungen mit mechanischen Spannungen
- PV 4.6.3
- Resistance to Chemicals of Automotive Top Coats, Gradient Oven Method
- PV 5106
- Prüfung des Verschleißschutzverhaltens
- PV 5605
- Radial Rolling Test
- PV 6601
- Acceptance Requirement, X-Ray Testing
- PV 6607
- Acceptance Requirements
- PV 6609
- Acceptance Requirements
- QP A001
- Prelube, Hot Melt, Blank Washing Oil, Drawing Compound, Slushing Oil (General) ; Quality Requirements
- QP F067
- Two-Component Clear Coat (Refinishing Paint) ;Quality Requirements
- QP P08
- Nonwoven Fabrics for Vehicle Protection ; Quality Requirements
- QP R007
- Cavity Flooding Wax ;Quality Requirements
- QP R015
- Self-Adhesive Films ; Quality Requirements
- TL 027
- Sr-veredelte eutektische AlSi-Legierungen ; Werkstoffanforderungen
- TL 055
- AlSiMg Alloy, Sr-Refined, Artificially Aged ; Material Requirements
- TL 1010
- Materials for Vehicle Interiors ; Burning Behavior, Material Requirements
- TL 1355
- unlegierter Baustahl ; Werkstoffanforderungen
- TL 152
- Powder Paint for Cylinder Block and Crankcase Surface Protection Requirements
- TL 161
- Lackierung auf Kunststoffaußenteilen ; Anforderungen und Prüfungen der Porsche AG
- TL 181
- Verchromte Leichtmetallräder ; Oberflächenschutzanforderungen
- TL 182
- Inorganic Protective Coating on Aluminum PartsSurface Protection Requirements
- TL 187
- Kugelzapfen nitrocarburiert-beschichtet ; Oberflächenschutzanforderungen
- TL 191
- paint coating on rear muffler ; Paint adhesion test
- TL 196
- Duplex Coating Systems for Small Parts and Bulk Parts ; Surface Protection Requirements
- TL 203
- Decorative Chrome Plating (Ni-Cr Coatings) on Metal Components ; Surface Protection Requirements
- TL 211
- Paint Coatings on Exterior Plastic Parts; Requirements
- TL 212
- Oxide Coatings on Aluminum Parts ; Surface Protection Requirements
- TL 214
- Coating with Zinc-Dust Paint ; Surface Protection Requirements
- TL 215
- Electroplated Chromium and Nickel/Chromium Coatings for Piston Rods ; Surface Protection Requirements
- TL 216
- Corrosion Protection on Half Shafts ; Surface Protection Requirements
- TL 217
- Zinc Coatings ; Surface Protection Requirements
- TL 218
- Body Color Multicoat Paint on Metallic Exterior Body Components Requirements
- TL 222
- Corrosion Protection Coatings for Brake Lines Surface Protection Requirements
- TL 226
- Paintworks on Materials Used in the Vehicle Interior Trim Requirements
- TL 227
- Single-Layer Paint of Zinc-Coated Metal Surfaces ;Surface Protection Requirements
- TL 233
- Non-Electrolytically Applied Zinc Flake Coatings with Top Coat ; Surface Protection Requirements
- TL 238
- Surface Protection, Steel Disk Wheels ; Surface Protection Requirements
- TL 239
- Surface Protection for Alloy Wheels Requirements
- TL 240
- Thin-Layer Zinc Phosphating ; Surface Protection Requirements
- TL 241
- Gleitbeschichtungen für Schließsysteme ; Oberflächenschutzanforderungen
- TL 244
- Zinc/Nickel Alloy Coatings ; Surface Protection Requirements
- TL 245
- Non-Electrolytically Applied Zinc Flake Coatings ; Surface Protection Requirements
- TL 256
- Powder Paint on Metal Surfaces ; Surface Protection Requirements
- TL 260
- Paintwork of Metal Surfaces ; Surface Protection Requirements
- TL 261
- Painting on Coil Springs ; Surface Protection Requirements
- TL 262
- Paint Finish of Chassis Parts ; Corrosion Protection
- TL 471
- Seat Belt Systems and Height Adjustment ASSY ; Material and Functional Requirements
- TL 52018
- Double-Sided Foam Adhesive Tape ; Materials Requirements
- TL 52038
- Labels ; Self-Adhesive, Material Requirements
- TL 52146
- Central Hydraulic System Fluid ; Lubricant Requirements
- TL 52162
- Factory-Fill-for-Life Automatic Transmission Fluid (ATF) ; Lubricant Requirements
- TL 52231
- ABS and PC Polymer Blends ; Material Requirements
- TL 52283
- Polypropylene, Elastomer-Modified, Talc- or Mineral-Modified ; Material Requirements
- TL 52288
- Polyamide, Mineral-Reinforced, Finished Parts ; Material Requirements
- TL 52428
- Protective Decorative Film ; Component Requirements
- TL 52437
- Polycarbonate Headlamp Outer Lenses with Functional Coating ; Materials Requirements
- TL 52440
- PA 6 glasfaserverstärkt, Fertigteile ; Werkstoffanforderungen
- TL 52451
- Painting of Metallic Decorative Add-on Parts for the Exterior Requirements
- TL 52452
- Polypropylen mit erhöhter Kristallinität ; Werkstoffanforderungen
- TL 52464
- Wheel Trim Elements ASSY Requirements
- TL 52631
- Test Scope for Material Data Sheets
- TL 52671
- PMMA, High Gloss Trims for the Exterior ; Material Requirements
- TL 52674
- Folienhinterschäumte Außenteile in Hochglanzoptik Prüfumfang für Bauteile
- TL 52680
- Components Made of Long-Fiber-Reinforced or Continuous-Filament ; Reinforced Plastic Composites (FRP) ; Materials and Component Requirements
- TL 527
- ABS Graft Polymer, Finished Parts ; Material Requirements
- TL 52704
- EPDM Body Seals ; Material Requirements
- TL 52711
- cd Enhancing Underbody Panels
- TL 528
- Chrome-Plated Plastic Parts ; Materials Requirements
- TL 534
- Polyamid 6, Fertigteile ; Werkstoffanforderungen
- TL 592
- Reflective Coatings on Mirror Glass ; Material Requirements
- TL 766
- Brake Fluid ; Material Requirements
- TL 774
- Ethylene Glycol-Based Coolant Additive ; Material Requirements
- TL 788
- Low-Temperature Lubricating Grease ; Lubricant requirements
- TL 80260
- fuel filter Functional Requirements
- TL 80286
- Refrigerant Heat Exchanger ; Functional Requirements
- TL 82132
- Charge Air Coolers ; Functional Requirements
- TL 82316
- R134a/R1234yf Refrigerant Lines ; Functional Requirements
- TL 82406
- Heater Cores ; Functional Requirements
- TL 82436
- Frontklappenscharnier ; Ein- und Mehrgelenk
- TL 82526
- Fahrgelenke ; Anforderungen und Prüfbedingungen
- TL 874
- Radiator ; Functional Requirements
- TL 934
- Wiper Systems ;Functional and Materials Requirements
- VW 01137
- Cleanliness Requirements for Components that Convey Coolant
- VW 13750
- Surface Protection for Metal Parts ; Surface Protection Types, Codes
- VW 2.8.1
- Elastomers ; Materials Requirements and Testing
- VW 44045
- Polypropylene, Finished Parts ; Material Requirements
- VW 50002
- Whole Vehicle ; Test Media ; Material Compatibility
- VW 50014
- General Requirements for Components and Semi-Finished Products ; Requirements and Tests
- VW 50099
- Foundry and Casting Technology Definitions
- VW 50121
- Acceptance Requirements for Surface Appearance
- VW 50125
- Polyamide 6 ; Finished Parts in the Passenger Compartment ; Material Requirements
- VW 50129
- Bonded Coating-Covered Body SealsRequirements and Tests
- VW 50133
- PA66 for Finished Parts Outside the Vehicle Interior ; Requirements on Materials
- VW 50179
- Emissionsverhalten bei Bauteilen im Fahrzeuginnenraum
- VW 50180
- Emission Behavior
- VW 50185
- Resistance to Open-Air Weathering
- VW 50190
- Visual Evaluation of Chrome Surfaces
- VW 50194
- Toleranzfestlegung und Bewertung der Sparkling- und Graininess-Differenzen von Effektlacken
- VW 50195
- Colorimetric Evaluation of Automobile Paint Coatings
- VW 50554
- Requirements on Standard Atmospheres
- VW 75141
- Test Specification
- VW 78001
- Kühlmittelsystem
- VW 80000
- General Requierements ; Test Conditions and Test
- VW 80101
- General Test Conditions
- VW 80972
- General Requirements and Measurement Conditions
- VW 91101
- Avoidance of Hazardous Substances
- VW 96023-2
- Teil 2: nach modifiziertem Klimawechseltest nach VW 96380
- VW 96076
- Allgemeine Konstruktionshinweise, Korrosionsklassen und Zoneneinteilung
- VW 96135
- Interieur / Exterieur - Oberflächendekore ; Kunststoffbauteile mit elektrolytisch abgeschiedener Metalloberfläche ;Anforderungen und Prüfungen
- VW 96142
- Acryl-Schaumband, beidseitig selbstkebend
- VW 96168
- Lacke und Anstrichstoffe ; Anforderungen und Prüfungen
- VW 96183
- Vehicle Interior ; Surface Decorative Materials – Coating, Pad Printing, and Hot Stamping ; Requirements and Tests
- VW 96207
- Lackierung / Pulverbeschichtung metallischer Fahrzeugteile ; Anforderungen und Prüfungen
- VW 96208
- Pulverlackierung -Oberfläache x 652 ; Anforderungen und Prüfungen
- VW 96210
- Anodisches Oxidieren - Eloxalschichten (w625, w630, w640) ; Anforderungen und Prüfungen
- VW 96288
- Dämmmaterial
- VW 96292
- Schläuche für Scheibenwaschanlagen ; Anforderungen und Prüfungen
- VW 96368
- Fahrwerk; Fahrwerksgelenke ; Anforderungen und Prüfungen
- VW 96378
- Prüfung im trocken-heißem Klima/ im feucht-warmen Klima
- VW 96379
- Klimawechseltest
- VW 96380
- Corrosion Test – Modified Environmental Cycle Test
- VW 96386
- Color Inspection
- VW 96390
- Determination of volatile organic emissions
- VW 96408
- Peel Test
- VW 96424
- Emissionsverhalten - Thermodesorptionsanalyse
- VW 96430
- Unterbodenschutzverkleidungen - Sandwichbauweise (Anforderungen und Prüfungen)
- VW 96446
- Prüfverfahren zur Eigenschaftsbestimmung
Volvo
- 42201
- MUD-TEST
- 1282044
- TYRE WHEEL ASSEMBLY
- 20712053
- COMPRESSED AIR TANK
- 31800062
- ALLOY WHEEL, GENERAL
- 31818317
- CHROMIUM ON HANDLE – SUPPLIER_10/2013
- 88200001
- Sun tan lotion test
- 000078/3
- Laboratory Corrosion test of painted light-metal wheels-CORWHEEL
- NOTE-TREG 31846536
- DRIVER AIRBAG SPA
- STD 1021,2
- Scribing of a surface coated test object and evaluation of the propagation from scribe when corrosion testing
- STD 1024,2844
- Peel adhesion (180°)
- STD 1024,7132
- Stone chip resistance
- STD 1024,7134
- Abrasion - organic materials
- STD 1024,7135
- Abrasion resistance- Abrasion resistant coatings
- STD 1026,1122
- Heat resistance -plastic
- STD 1026,4121
- Moisture resistance accelerated test- Paints and enamels
- STD 1026,5172
- Determination of colour in colour-matching booth
- STD 1026,5272
- Gloss - Paints and enamels
- STD 1026,8177
- Chemical resistance - Surface treatments
- STD 1026,8201
- Grey scale - Determination of changes in colour
- STD 1026,8202
- Grey scale for assessing staining
- STD 1026,8243
- Light fastness 60 °C
- STD 1026,8432
- Colour fastness to rubbing - Rubber, plastics and textiles
- STD 1026,8433
- Colour fastness to rubbing with organic solvents -textiles
- STD 1026,8434
- Colour fastness to rubbing- paint and enamels
- STD 1027,051
- Evaluation degrees blistering of paints - Paints and enamels
- STD 1027,1372
- Accelerated outdoor exposure- Scab corrosion test
- STD 1027,1375
- Corrosion resistance-Accelerated atmospheric corrosion testing - Volvo Indoor Corrosion Test (VICT)
- STD 1027,14
- Accelerated corrosion test - Atmospheric corrosion
- STD 1027,2711
- Fogging organic materials
- STD 1027,3371
- Climate ageing (Crack formation) -Paints and enamels
- STD 1027,3375
- Moisture resistance in tropical cabinet Chemical materials
- STD 1027,6132
- Test liquids
- STD 1029,5471
- Adhesion, water spraying under high pressure Paints and enamels
- STD 1029,5472
- Adhesion, cross-cut test Paints and enamel
- STD 1029,5473
- Adhesion - Paints and enamels
- STD 121-0001
- Painting Y 600
- STD 121-0002
- Painting Y 650
- STD 121-0003
- Cathodically protective surface treatment with friction requirement Y 1000
- STD 121-0006
- Cathodically protective surface treatment for tubes und tube fittings Y 400
- STD 1266,1
- Decals 96610 -Self-adhesive, permanent application
- STD 1283,1
- Solvent 98310 - High aromatic content
- STD 420-0001
- Evaluating degrees blistering of paints
- STD 420-0003
- Fogging organic materials
- STD 420-0004
- Test liquids
- STD 423-0002
- Plastics - Determination of temperature of deflection under load
- STD 423-0009
- Adhesion -Paints and enamels, knife technique
- STD 423-0012
- Adhesion, cross-cut test- Paints and enamels
- STD 423-0015
- Adhesion, water spraying under high pressure Paints and enamels
- STD 423-0018
- Moisture resistance in tropical cabinet Chemical materials
- STD 423-0024
- Extensibility- paints and panels
- STD 423-0030
- Scratch resistance, Erichsen Pen- Organic materials
- STD 423-0037
- Colour fastness to rubbing-Rubber, plastics, textiles, paints and varnishes
- STD 4234
- Paints and varnishes - Determination of adhesion when subjected to high-pressure spraying with water
- STD 429-0001
- Odour of trim materials in vehicles-organic materials
- STD 4445
- Accelerated corrosion test, version II (ACT2)
- STD 5511,71
- Determination of friction properties for screw joints
- STD 5711,101
- Outdoor testing
- STD 5712,102
- Adhesion - file test
- STD 5712,104
- Adhesion - burnishing test
- STD 5732,12
- Chromium plating Y120
- STD 5750,12
- List of colours
- STD 5751,5
- Painting Y 500 - Metal substrates
- STD 5751,55
- Painting Y 550-Plastics substrates
- VCE 5751,61
- Specification of requirements for paint systems
- VCS 1021,19
- Conditioning of painted test panels before testing
- VCS 1021,29
- Scribing of coated test object and evaluation of propagation of corrosion from scribed line
- VCS 1024,11419
- Extensibility
- VCS 1024,31139
- Erichsen Pen
- VCS 1024,31239
- Hardness
- VCS 1024,369
- Mar resistance of top coats in brush-type car wash
- VCS 1024,67639
- Determination of the throwing power of electrocoat paint (EC paint)
- VCS 1024,71329
- Stone chip resistance
- VCS 1024,7136
- Stone chip resistance
- VCS 1025,89
- Determination of film thickness
- VCS 1026,51729
- Assessment of colour in light booth
- VCS 1026,52729
- Gloss
- VCS 1026,52749
- Paint surface texture
- VCS 1026,81779
- Paints and enamels - chemical resistance
- VCS 1026,81819
- Chemical resistance under heat influence
- VCS 1026,82439
- Light fastness 60 °C
- VCS 1026,84349
- Colour fastness to rubbing
- VCS 1027,0519
- Evaluation degrees for blistering of paints
- VCS 1027,13729
- Accelerated outdoor exposure
- VCS 1027,139
- Blister corrosion
- VCS 1027,1449
- Cyclic atmospheric corrosion test with salt load - accelerated corrosion test, version II - ACT II
- VCS 1027,149
- Accelerated corrosion test
- VCS 1027,159
- Edge coverage of electrocoat paints
- VCS 1027,2719
- Organic materials – Fogging
- VCS 1027,2729
- Organic materials - odour of trim materials in vehicles
- VCS 1027,2739
- Determination of formaldehyde emission from components in vehicle interiors
- VCS 1027,2749
- Determination of organic emission from non-metallic materials in vehicle interiors
- VCS 1027,33719
- Climate ageing (Crack formation)
- VCS 1027,33759
- Moisture resistance in tropical cabinet
- VCS 1027,3389
- Outdoor testing in subtropical climate
- VCS 1027,339
- Accelerated light exposure of exterior coatings
- VCS 1027,3399
- Photooxidation resistance of clear coats measured by infrared spectroscopy
- VCS 1027,61329
- Test liquids
- VCS 1029,54719
- Paints and enamels - adhesion, water spraying under high-pressure
- VCS 1029,54729
- Adhesion, cross-cut test
- VCS 1029,54729
- Adhesion, cross-cut test
- VCS 1281,219
- Electrocoat paint (EC paint) 98121
- VCS 1283,19
- Solvent 98310
- VCS 5023,509
- Symbols, designations and general drawing methods
- VCS 5031,19
- Flammability of interior materials
- VCS 5036,5
- VCC Restricted Substance Management Standard (RSMS)
- VCS 5036,5
- VCC Restricted Substance Management Standard (RSMS)
- VCS 5068,8019
- Rules and procedures for the assessment of surface texture
- VCS 5711,1019
- Outdoor testing
- VCS 5713,1059
- Test for presence of leachable nickel
- VCS 5715,1029
- Evaluation of degradation of paint coatings
- VCS 5737,19
- Cathodically protective surface treatment with friction requirement Y100
- VCS 5751,5119
- Paint refinishing system
- VCS 5751,59
- Paint systems
Contact persons
Did you not find the sought standard?
Do you have questions or would you like an individual consultation?
Contact or employees for technical questions directly or by email.
Analytics
Dr. Ute Holzhausen
Tel. +49 391 6090 238
E-Mail: ute.holzhausen@ilf-magdeburg.de
Application technology
Cornelia Dreyer
Tel. +49 391 6090 215
E-Mail: cornelia.dreyer@ilf-magdeburg.de
Materials testing
Dr.-Ing. Susanne Bender
Tel. +49 391 6090 239
E-Mail: susanne.bender@ilf-magdeburg.de